HARDNESS STABILIZER POLYCARBOX

Size:

Color:

Product Short Description: Scale Inhibitor 4300 Rx is a high performance polymer based scale inhibitor.
Product Technical Specification:

Typical Properties :

Appearance Liquid clear
Type Maleic Multipolymer
Odour Odourless or Mild odor

Molecular weight¹

 2000
pH 6.5 - 7.50
% Total solids 50
% Actives 60-90
Viscosity, as is, mPa.s/cps² 400-1200
Remarks:
Images: Alt


Clog Controller Biocide

Size:

Color:

Product Short Description: Strong algae depressant fully compatible with alkalizing and flocculating agents normally used in cooling / boiler water. Algae growth is the main cause of colour in water. Routine and weekly additions of RXSOL-40-4009-050 establish a buffer action to control very rapid algae growth.
Product Technical Specification:
Remarks:

Clog Controller Biocide RXSOL-40-4009-050 should be dosed periodically at a rate of 75 - 150 ppm of the total system volume. In a badly fouled system an initial dosage rate of up to 250m1/m3 may be required which can be reduced once control is gained.In order to comply with Health & Safety recommendations Clog Controller Biocide RXSOL-40-4009-050 should be alternated with another non-oxidising or oxidizing biocide. It is always advisable to carry out a 'Control Of Substances Hazardous to Health' (COSHH) assessment before use.

Images: Alt


Heat Transfer Liq Inhibited

Size:

Color:

Product Short Description: Heat Transfer water mix propylene glycol liquid
Product Technical Specification:

 

Main Ingredients   : PROPYLENEGLYCOL (1,2-) 94%
Inhibitors and
water
 
6
Inhibitors and water
 : 6 %
Colour Bright : Clear
pH of solution : 8.8
Odour            : PRACTICALLY ODOURLESS
Solubility in water        : SOLUBLE
     
Boiling point         : 162 oC
Freezing point       : -32 oC
Viscosity     : 58.1 cp at 20 oC
Reverse Alkalinity         : Minimm 15.0 ml
Vapour pressure    : .07 mbar at 20oC
Skin absorption/irritation       : YES
TLV       Country     :  
Pollution category    1994       : III
 

 

Remarks:

Propylene glycol is tolerated well by the skin and shouldn't cause redness or irritation. Propylene glycol is a penetration-enhancing humectant.
 

Propylene Glycol USP is a widely used ingredient in pharmaceutical, food, cosmetic, personal care, flavors and animal feed applications; an overview of typical uses of Propylene Glycol USP as below.It must be emphasized that it is the user’s responsibility to consult area and country-specific regulations for details of approved use.

  1. Pharmaceuticals - Solvent for active ingredients in oral, and topical products.
     
  2. Cosmetics & Personal Care - Solvent, coupling agent, carrier, emulsion stabilizer, softening agent, viscosity modifier and humectant in many types of cosmetics and personal care products such as skincare, sun care, shampoo, bath/shower products, toothpastes, mouthwashes, shaving products and baby care products.
     
  3. Flavors & Fragrances - Solvent and extraction solvent of flavors and fragrances for applications in food, beverages, perfumes and cosmetics.
     
  4. Food - Various applications as a direct food additive (E 1520) such as a carrier or carrier solvent for colors, emulsifiers, antioxidants and enzymes (in Europe with maximum 1 g/kg in human foodstuffs), and humectant and stabilizer in fruits, vegetables and bakery goods (except in Europe). Propylene Glycol USP is also applied in indirect contact food applications, such as a low temperature heat-transfer fluid in the brewing, dairy and ice cream industries and for food storage facilities, an equipment cleaner fluid or a solvent for printing inks.
     
  5. Pet foods & Animal Feed - Humectant, emulsifier, preservative, solvent foradditives, energy source and aid for prevention of ketosis (acetonemia) in dairycattle. In EMEA a specific tailor made Propylene Glycol Animal Feed is offered forthis application.
Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


AMEROL Evaporator Treatment

Size:

Color:

Product Short Description: AMEROL Evaporator Treatment: Advanced Scale & Foam Control for Evaporators
Product Technical Specification:
CharactersItics   Properties
Appearance Thermal Firmness Clear  yellow liquid 250° C            By keeping heat transfer surfaces free of scale, Ensures that the evaporator works at maximum efficiency.
Density In g/cm3 at 15°C: 1.1

Permits more efficient evaporation.
pH (1 Vol%) 9

Reduces downtime and maintenance costs.
Compatibility   Concentrated, safe liquid, easy and economical dosing.
Metal No known effect

For use in both high pressure and vacuum evaporators
Rubber No known effect The antifoaming properties ensure that distillate quality is high
Packaging

20 / 25 ltr

Improves the quality of distilled water
Remarks:

Key Benefits for Maritime & Desalination Operations of AMEORL Evaporator Treatment Chemical:

 

Feature Benefit
Dual-action (scale + foam control) Simplifies chemical dosing and inventory
Liquid form Easy to handle, mix, and dose
Compatible with high salinity water Effective even in extreme seawater conditions
High thermal stability Reliable at elevated temperatures in flash evaporators
Environmentally safe formulation Meets marine discharge compliance standards
Improves evaporator throughput Fewer shutdowns, more water output per hour

 

RXSOL-51-6001-025 is a concentrated  solution of a POLYELECTROLYTE  polymer and Antifoaming Agents for  use in SEA WATER evaporator  as a controller of scale and foam in side the  evaporators.  It can be used as a scale inhibitor  in the  feed water  to EVAPORATORS producing fresh water .

A liquid polymer-based evaporator treatment specially designed to control and prevent scale formation in evaporators

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


Antifoam Defoamer Elite M8

Size:

Color:

Product Short Description: Highly effective liquid antifoam formulated for controlling foaming and priming in seawater distillation plants compatible with most antiscalants
Product Technical Specification:

 

Appearance Clear to Pale Yellow Liquid

Water content		 4-5% w/w
Aqueous Emulsion Ready dispersible white milky emulsion
Specific Gravity at 25°/25°C 1
Odour Slight
Specific Gravity <1
Saponifaction Value 11-15 mg KOH/g
Remarks:

Low dose levels, typically in the range 0.05 to 0.1 mg/l in the seawater feed stream, depending on feed water quality. Activity is not dependent on temperature. No need to alter dose level if top brine temperature (TBT) changes. Negligible steam volatility and carry over into the distillate.

RXSOL-16-2066-200 is antifoam emulsion and its more concentrated antifoam emulsion. It has excellent candidates for controlling foam in amine and glycol dehydration units. This is suitable products for gas plants and have excellent stability in the presence of salts, resulting in reduced deposits on the plant’s equipment. RXSOL-16-2066-210  help preserves foam control under the severe conditions of a dehydrating unit. These conditions can remove water from other antifoam emulsions, rendering them immediately inactive.

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


Antifoam Defoamer AF10

Size:

Color:

Product Short Description: Highly effective liquid antifoam formulated for controlling foaming and priming in seawater distillation plants compatible with most antiscalants
Product Technical Specification:

 

Appearance Clear to Pale Yellow Liquid

Water content		 4-5% w/w
Aqueous Emulsion Ready dispersible white milky emulsion
Specific Gravity at 25°/25°C 1
Odour Slight
Specific Gravity <1
Saponifaction Value 11-15 mg KOH/g
Remarks:

Low dose levels, typically in the range 0.05 to 0.1 mg/l in the seawater feed stream, depending on feed water quality. Activity is not dependent on temperature. No need to alter dose level if top brine temperature (TBT) changes. Negligible steam volatility and carry over into the distillate.

RXSOL-51-2066-220 is antifoam emulsion and its more concentrated antifoam emulsion. It has excellent candidates for controlling foam in amine and glycol dehydration units. This is suitable products for gas plants and have excellent stability in the presence of salts, resulting in reduced deposits on the plant’s equipment. RXSOL-51-2066-220  help preserves foam control under the severe conditions of a dehydrating unit. These conditions can remove water from other antifoam emulsions, rendering them immediately inactive.

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


Urea Solution 35

Size:

Color:

Product Short Description: Liquid Urea is a crystal clear aqueous solution of urea.
Product Technical Specification:

 Chemical & Physical Properties

Chemical Formula CO(NH2)2
CAS Number 57-13-6
Molecular Weight 60.056
Specific Gravity  1.140
pH 6.5 - 8.5
Salt-Out Temp 62°F (18°C)
Colour Clear Liquid
Odor Slight ammonia smell

Typical  Analysis :

Urea  23% Nitrogen 50%
Turbidity 5 ppm
pH 8.5 Max
Ammonia  0.03%
Biuret  < 0.25%
Ash 35  ppm
Iron 2 ppm
Chloride 10 ppm
Color - Max 0 (APHA)
Alkalinity - wt (NH3) Max

 0.05%

 
Remarks:
Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


Descalant Chemical

Size:

Color:

Product Short Description: Scales are damaging the boiler because they interfere with the heat transfer and can lead to overheating and eventually, boiler rupture , To increas usable life of cleaned equipment , it is safe and effective way to remove scale deposits from all
Product Technical Specification:

 

• Automotive - Closed Circuit Cooling, Dynamometers, Extruders, Molders, Radiators, Welders

• Bottling - CO2 Generators, Heaters, Exchangers, Rinse Tanks, Sterilizers, Washers

. HOUSE HOLD - Dissolves hard and old lime scale deposits from your appliances. It extends the life of the appliance and saves running cost. It can be used in appliances such as Washing Machines, Dish Washers, Geysers, Steam Iron, Coffee Makers, Bath Tubs, Bathroom Fixtures etc.

• Buildings - Chillers, Cooling Towers, Pipework

• Chemicals - Dryers, Extruders, Kettles, Mixers, Reactors, Scrubbers, Vacuum Pumps

• Food - Condensers, Ice Machines, Kathabars, Refrigeration Equipment, Steam Tables

• Manufacturing - Chillers, Compressors, Furnaces, Quenchers, Vacuum Pumps

• Metals - Bearings, Castings, Fans, Hearth & Vacuum Furnaces, Shelters, Sprays

• Mining - Bearings, Conveyors, Filters, Presses, Process Lines, Radiators

• Paper- Calendar Mill Rolls, Caustic Lines, Scrubbers, Compressors, Liquor Tanks, Pulverizers, Vacuum Pumps

• Pharmaceutical- Exchangers, Loop Systems, Kathabars, Pumps, Reactors, Stills, Sterilizers

• Refinery - Compressors, Converters, Crackers, Exchangers, Piping, Pumps

• Rubber/Plastics - Banbury Mixers, Calendar & Mill Rolls, Extruders, Injection Molders, Molds, Temperature Control Units, Throat Coolers, Towers, Tubers

• Steel - Bearings, ConCast Units, Generators, Hearths, Spangle Units, Furnaces

• Textile - Air Washers,Compressors, Condensers, Exchangers, Extruders,Towers

 

Boilers

Condensers

Filters

Heat Exchangers

Kettles & Tanks

Pipelines

Pots

Reactors

Steam Jackets

Bath Rooms and Showers

Metal Processing and much more!


 

Applications


  Automotive
  Bottling
  Chemicals
  Food

  - Closed Circuit Cooling

  - Dynamometers

  - Extruders

  - Molders

  - Radiators

  - Welders
  - CO2 Generators

  - Heaters

  - Exchangers

  - Rinse Tanks

  - Sterilizers and Washers
  - Dryers

  - Extruders

  - Kettles

  - Mixers

  - Reactors

  - Scrubbers

  - Vacuum Pumps
  - Condensers

  - Ice Machines

  - Kathabars

  - Refrigeration Equipment

  - Steam Tables

  Manufacturing
  Metals
  Mining
  Paper

  - Chillers

  - Compressors

  - Furnaces

  - Quenchers

  - Vacuum Pumps
  - Bearings

  - Conveyors

  - Fans

  - Hearth & Vacuum Furnaces

  - Shelters

  - Sprays
  - Bearings

  - Conveyors

  - Filters

  - Presses

  - Process Lines

  - Radiators
  - Calendar Rolls

  - Mill Rolls

  - Caustic Lines

  - Scrubbers

  - Compressors

  - Liquor Tanks

  - Pulverizers

  - Vacuum Pumps

  Pharmaceutical
  Refinery
  Rubber & Plastics
  Steel

  - Exchangers

  - Loop Systems

  - Kathabars

  - Pumps

  - Reactors

  - Stills

  - Sterilizers
  - Compressors

  - Converters

  - Crackers

  - Exchangers

  - Piping

  - Pumps
  - Banbury Mixers

  - Calendar & Mill Rolls

  - Extruders

  - Injection Molders

  - Molds

  - Temperature Control - Units

  - Throat Coolers

  - Towers and Tubers
  Bearings

  ConCast Units

  Generators

  Hearths

  Spangle Units

  Furnaces

  Textile
  Utilities
  Other Applications
   

  - Air Washers

  - Compressors

  - Condensers

  - Exchangers

  - Extruders and Towers
  - Boilers

  - Turbines

  - Transformers

  - Cooling Towers

  - Air Compressors

  - Hydrogen Coolers

  - Lube Oil Heat Exchangers
  - Ball Mills

  - Demisters

  - Evaporators

  - Locomotives

  - Absorption Units

  - Diesel Generators

  - Induction Furnaces
Remarks:

Suggestion ::: Our daily descaling works helps to share helpful tricks to dissolve hard scale easily, Always use 5-10 %  our new generation hard scale deposit remover powder RXSOL-11-1102-025 . Addition of RXSOL-11-1102-025 helps to clean 100% scale from system .

Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


Antiscalant RXSOL ORG EV

Size:

Color:

Product Short Description: Antiscalant RXSOL ORG EV is a high performance liquid product for the control of alkaline scaling calcium carbonate and magnesium hydroxide in all types of seawater distillation plants
Product Technical Specification:

Physical Properties
 

Appearance : Clear Amber Liquid
Odour : Slight
Solids content : 47-53% w/w
Specific gravity : 1.16 to 1.19 at 20/20 oC
pH : 2 maximum
Boiling range (760 mm Hg) : 100-102°C (212-215°F)
Freezing point : 0 to -12oC
Solubility in Water : Miscible
Iron PPM : <10
Lead PPM : <10
 
Remarks:
Images: Alt
Get MSDS
Get Technical Bulletin
Connect On Whats App


RXSOL Altreat 400

Size:

Color:

Product Short Description: RXSOL Altreat 400 also impairs crystal growth, modifying the crystal structure to create a soft sludge byproduct that does not adhere to heat transfer surfaces. During the distillation process, the formation of scale on heat transfer surfaces can significantly reduce heat transfer efficiency and inc
Product Technical Specification:
Technical Specifications:
  • Highly concentrated liquid delivers substantial savings since up to 40% less solution than other polymaleates is required to achieve the same effect.
  • Highly effective, but gentle, solution does not harm the environment or heat exchanger tubes, plates, gaskets or glue.
  • Highly versatile scale inhibitor delivers effective performance while operating in temperatures up to 80ºC.Helps maintain heat transfer rates, thus improving process performance, reducing energy costs and prolonging heat exchanger lifetime.Increases the efficiency and performance of the equipment,reducing total operation and maintenance costs.
  • Recommended operating temperatures: 50°–80°C.

 specification:-

Appearance: Colourless
Specific gravity (water=1) > 1

Viscosity:		 600 mm2/s at 23°C
Flash point: >100°C
pH: 6-8
Miscibility with water In all proportions
Remarks:
Images: Alt
stock-clearance.png